substitutions:
  name: thr320d_filtre_bb04f0
  friendly_name: "filtration"
  project_name: "Filtration piscine"
  project_version: "1.0"
  light_restore_mode: RESTORE_DEFAULT_OFF

esphome:
  name: "${name}"
  # supply the external temp/hum sensor with 3v power by pulling this GPIO high
  on_boot:
    - priority: 90
      then:
      - switch.turn_on: ${name}_sensor_power

esp32:
  board: nodemcu-32s

api:
  encryption:
    key: "zOAo/IyJfGlFafVzPae/pCJZQtGFRWc7i+O9ZXfRY+c="

ota:
  - platform: esphome
    password: "5e0d993d03804b33e56142c07cae7526"

logger:
  baud_rate: 0

web_server:
  port: 80

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: !secret ap_ssid_pool
    password: !secret ap_pass_pool

captive_portal:

one_wire:
  - platform: gpio
    pin: GPIO25

# This will take care of the display automatically.
# You don't need to tell it to print something to the display manually.
# It'll update every 60s or so.
display:
  platform: tm1621
  id: tm1621_display
  cs_pin: GPIO17
  data_pin: GPIO5
  read_pin: GPIO23
  write_pin: GPIO18
  lambda: |-
    it.printf(0, "%.1f", id(${name}_temp).state);
    it.display_celsius(true);
    /*it.printf(1, "%.1f", id(${name}_temp).state/10);
    /*it.display_kwh(true);
    /*it.printf(1, "%.1f", id(${name}_humi).state);
    it.display_humidity(true);*/

binary_sensor:
  # single main button that also puts device into flash mode when held on boot
  - platform: gpio
    pin:
      number: GPIO0
      mode: INPUT_PULLUP
      inverted: True
    name: "${friendly_name} Button"
    on_click:
      - max_length: 350ms # short press to toggle the relay
        then:
          switch.toggle: mainRelayVirt
      - min_length: 360ms # long press to do...
        max_length: 3s
        then:
          switch.toggle: dryContRelay
      - min_length: 10s # very long press to reset
        max_length: 20s
        then:
          - switch.turn_on: ${name}_restart
  - platform: status
    name: "${friendly_name} Status"

switch:
  # virtual switch to represent the main relay
  # as far as I know, we have no way to confirm the real state
  - platform: template
    id: mainRelayVirt
    name: "Pompe"
    turn_on_action:
      - switch.turn_on: mainRelayOn
      - switch.turn_on: ${name}_onoff_led
    turn_off_action:
      - switch.turn_on: mainRelayOff
      - switch.turn_off: ${name}_onoff_led
    assumed_state: True
    optimistic: True
    #restore_state: True
    #restore_mode: ALWAYS_ON

  # internal momentary switch for main relay ON
  - platform: gpio
    id: mainRelayOn
    internal: True
    pin:
      number: GPIO19
    on_turn_on:
      - delay: 500ms
      - switch.turn_off: mainRelayOn
    restore_mode: ALWAYS_OFF

  # internal momentary switch for main relay OFF
  - platform: gpio
    id: mainRelayOff
    internal: True
    pin:
      number: GPIO22
    on_turn_on:
      - delay: 500ms
      - switch.turn_off: mainRelayOff
    restore_mode: ALWAYS_OFF

  # dry contact relay switch
  - platform: gpio
    id: dryContRelay
    name: "Extension"
    pin:
      number: GPIO4
    on_turn_on:
      - switch.turn_on: ${name}_ext_led
    on_turn_off:
      - switch.turn_off: ${name}_ext_led

  # Leftmost (red) LED that's used to indicate the relay being on/off
  - platform: gpio
    id: ${name}_onoff_led
    pin:
      number: GPIO16
      inverted: true

  # Rightmost (green) LED; use as dry contact indicator
  - platform: gpio
    id: ${name}_ext_led
    pin:
      number: GPIO13
      inverted: true

  # This is needed to power the external temp/humidity sensor.
  # It receives 3v from this pin, which is pulled up on boot.
  # TODO: This should probably be an internal switch.
  - platform: gpio
    pin: GPIO27
    id: ${name}_sensor_power
    restore_mode: ALWAYS_ON

  - platform: restart
    name: "Filtration Restart"
    id: ${name}_restart
    icon: "mdi:restart"

light:
  # The middle (blue) LED is used as wifi status indicator.
  - platform: status_led
    id: wifi_status_led
    name: "Wifi"
    pin:
      number: GPIO15
      inverted: true

sensor:
  - platform: dallas_temp
    name: "Température eau"
    id: ${name}_temp
    address: 0xfe3ce504578d3c28
    update_interval: 1s

climate:
  - platform: thermostat
    name: "${friendly_name} Climate"
    sensor: ${name}_temp
    default_preset: Home
    preset:
      - name: Home
        default_target_temperature_low: 31 °C
        mode: heat
    min_heating_off_time: 300s
    min_heating_run_time: 300s
    min_idle_time: 30s
    heat_action:
      - switch.turn_on: mainRelayVirt
    idle_action:
      - switch.turn_off: mainRelayVirt
    heat_deadband: 0.5 # how many degrees can we go under the temp before starting to heat
    heat_overrun: 0.5 # how many degrees can we go over the temp before stopping

text_sensor:
  - platform: wifi_info
    ip_address:
      name: "Addresse IP"
      disabled_by_default: true

interval:
  - interval: 30s
    then:
      if:
        condition:
          wifi.connected:
        then:
          - light.turn_on: wifi_status_led
        else:
          - light.turn_off: wifi_status_led